Covers: 2008, 2009, 2010, 2011 Yamaha Raider, Raider S VX1900 Pages: 494 Format: PDF file File size: 23mb Compatibility: Windows/Mac/Tablet File details: Bookmarked: Yes, Searchable: Yes, Printable: Yes Notes: High definition service manual This downloadable PDF manual contains detailed service procedures, illustrations and diagrams for your 2008-2011 Yamaha Raider or Raider S motorcycle. Additionally, it includes all electrical systems. Whether you are a DIY or professional mechanic, this manual will save you time and money on repairs. Print off the service manual pages you need an toss them when they get dirty. Topics in the 2008-2011 Yamaha Raider, Raider S VX1900 Service Repair Manual:.
General Information. Motorcycle Specifications. Torque Specifications.
Inspection. Adjustments. Maintenance. Engine Service. Engine Overhaul. Cooling System.
Fuel System (EFI or Carb). Chassis. Body. Brakes. Suspension. Drivetrain.
Electrical System. Troubleshooting. Wiring Diagram. Appendices. Supplements. Index. And much more Example manual details (actual manual may vary): How does this work?
It’s simple – after purchasing this manual through our secure checkout, a download link will be sent to the email address you specify. You have up to 30 days to retrieve and save the file. After that it is yours for good. Have any questions or need more details?
Certified Master Tech is proud to offer motorcycle service repair manuals for your Yamaha Raider - download your manual now!
View and download yamaha r6s owners manual online r6s motorcycle pdf manual download also for yzfr6sx yzfr6sw. View and download yamaha ra700s 1994 service manual online ra700s 1994 boating equipment pdf manual download also for ra700t 1994 ra700bu 1996 ra700bv 1996 ra700bu 1997 ra700bv 1997 ra760u 1996 ra1100t 1995 ra1100u 1995 ra1100t 1996 ra1100u 1996 ra700s 1995 ra700at 1995. Download start on either the left or right side mirror these instructions start with the right side mirror pull back the rubber boot covering the mirror mount 1 2 3 remove the accessory compartment cover. The 2018 fifa world cup was the 21st fifa world cup an international football tournament contested by the mens national teams of the member associations of fifa once every four years it took place in russia from 14 june to 15 july 2018 it was the first world cup to be held in eastern europe and the 11th time that it had been held in europe at an estimated cost of over 142 billion it.
Raider boat service repair manuals no user account needed raider boat service repair manuals. Castor power 26 strimmer manual. Raider boat service repair manuals page 2 no user account needed raider boat service repair manuals page 2. Our raider mitsubishi workshop manuals contain in depth maintenance service and repair information get your emanual now. Yamaha raider service repair and user owner manuals full online 766 boats were found that matched your search scroll down and click on the id or boat.
Yamaha raider for factory haynes service repair manuals yamaha raider repair manual pdf.
Remove the fairing lowers. For R1 owners, please remove the existing exhaust system from the EXUP valve rearward (EXUP valve is retained) and set aside. Save the stock exhaust clamp for reuse. For R6 owners, please disconnect the stock S-bend from the rear of the collector and set aside. Save the stock exhaust clamp for reuse (new clamp provided).
Save the stock end can mounting bolt for reuse as well. R1 owners only -Inspect the exhaust gasket. Replace if necessary (gasket provided). For R1 owners -Install the S-Bend to the rear of the EXUP valve, make sure the system fits flush.
Reuse the stock exhaust clamp to connect the S-bend to the valve. For R6 owners -Install the TiForce S-bend to the rear of the stock head pipes and collector. Make sure the system fits flush and snug. Reuse the stock exhaust clamp or the provided clamp and loosely attach for now. Install the TiForce end can to the S-bend tail pipe. Loosely attach the two rubber bands, stainless steel bands (K), and stay to the end can using the supplied 6mm hardware (H) and the hanger / stay arm (G).
See figure 1 for the assembly procedure. R1 owners -Place the bands approximately 180mm from the edge of the end can. See figure 2.
R6 owners -Place the bands approximately 195mm from the edge of the end can. See figure 2. R1 owners -Using the stock provided mounting point on the passenger footpeg, use the M10x45mm bolt and hardware to mount the end can loosely, allowing for some adjustment. Carefully align the two stainless bands so that theyare parallel to each other, and spaced properly on the can. Tighten the 6mm hardware (H).
Make sure that the rubber pads fully cover the bands (K). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire TiForce exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED.
Attach the supplied springs to secure the end can to the S-bend pipe using a spring installation tool if available. Make sure the exhaust system is free and clear of the bike. If necessary, adjust for proper clearance.
Go back and tighten all fasteners. Check that all fasteners are tightened per specifications, then start the motor and check for exhaust leaks. Reinstall the fairing lowers. The author of this manual has the conviction that the only way in which a meaningful and easy to follow text can be written is first to do the work himself, under conditions similar to those found in the average household. As a result, the hands seen in the photographs are those of the author. Even the machines are not new: examples that have covered a consider- able mileage were selected so that the conditions encountered would be typical of those found by the average owner.
Unless specially mentioned, and therefore considered essential, Honda service tools have not been used. There is invariably some alternative means of slackening or removing some vital component when service tools are not available and isk of damage has to be avoided at all costs.
Each of the six Chapters is divided into numbered Sections. Within the Sections are numbered paragraphs.
In consequence, cross reference throughout this manual is both straightforward and logical. When a reference is made ‘See Section 5.12′ it means Section 5, paragraph 12 in the same Chapter. If another Chapter were meant, the text would read ‘See Chapter 2, Section 5.12′. All photographs are captioned with a Section/paragraph number to which they refer and are always relevant to the Chapter text adjacent. Figure numbers (usually line illustrations) appear in numerical order, within a given Chapter.
1.1 therefore refers o the first figure in Chapter 1. Left-hand and right-hand descriptions of the machines and their component parts refer to the right and left of a given machine when the rider is seated normally. Motorcycle manufacturers continually make changes to specifications and recommendations, and these, when notified,mare incorporated into our manuals at the earliest opportunity.
We take great pride in the accuracy of information given in this manual, but motorcycle manufacturers make alterations and design changes during the production run of a particular n motorcycle of which they do not inform us. No liability can be ccepted by the authors or publishers for loss, damage or injury caused by any errors in, or omissions from, the information give Incoming search terms:. Always make a pre-ride inspection before you start the engine. You may prevent an accident or equipment damage. 2 Many accidents involve inexperienced riders.
Most countries require a special riding test or license. Make sure you are qualified before you ride. NEVER lend your motorcycle to an inexperienced rider. 3 Many car/motorcycle accidents happen because the car driver does not “ see the motorcyclist. Make yourself conspicuous to help avoid the accident that is not your fault:.
Wear bright or reflective clothing. Don’t drive in another motorist’s “blind spot” 4 Obey all national, and local laws and regulations Excessive speed is a factor in many accidents. Obey the speed limits am NEVER travel faster than conditions warrant. Signal before you make a turn or lane change.
Your size and manoeuvrability can surprise other motorists.5 Don’t let other motorists surprise you. Use extra caution at intersections, parking entrances and exits and driveways. 6 Keep both hands on the handlebars and both feet on the footrests while riding. A passenger should hold onto the motorcycle or the rider with both hands, and keep both feet on the passenger footrests. PROTECTIVE APPAREL 1 Most motorcycle accidents fatalities are due to head impact.
ALWAYS wear a helmet. You should also wear a face shield or goggles; boots, gloves, and protective clothing. A passenger needs the same protection. The exhaust system becomes very hot during operation, and it remains hot after operation. Never touch any part of the hot exhaust system. Wear clothing that fully covers your legs.
3 Do not wear loose clothing which could catch on the control levers, footrests, or wheels. Removing Your Old Filter and Beauty Cover In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4.
Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p. The bottommost bolt on the beauty cover will likely leak some oil when you remove it – it holds on the inner oil filter cover. Once you remove the beauty cover, you can remove the oil filter cover, and the oil filter Keep these two “O” rings, you’ll need them for the remote kit Old oil filter.
Toss it away; you’ll never need one again! Throw away the old filter, and carefully remove the orange and black “O” rings from the filter cover (see picture above). These two “O” rings will go on the new engine cap in the same order as on the old filter cover. “O” ring for bottom bolt. When the beauty cover and filter cover are removed, be sure not to lose the tiny “O” ring that the bottom bolt goes through. Preparing the Remote Oil Filter Kit Remove the orange and black “O” rings from the stock filter cover plate, and place them on the Remote Oil Filter Kit engine cap – black on the inside, orange on the outside – just like on the stock filter cover.
Incoming search terms:. GASOLINE IS HIGHLY FLAMMA- BLE: Always turn the engine off when refueling. Take care not to spill any gasoline on the engine or exhaust system when refueling.
Never refuel while smoking or in the vicinity of an open flame. Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time.
Always operate your motorcycle in an area that has adequate ventilation. Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following: The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over.
Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the fuel tank. If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash the affected area with soap and water and change your clothes.
Cover the throttle bodies to prevent anything from dropping into the engine. Remove the front seat and disconnect the battery.
(Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank.
(Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. Install the air cleaner box in reverse order of removal.
(Refer to Service Manual, Page 5-14) 6. Lower the fuel tank. (Refer to Service Manual, Page 5-3) 7. Remove the upper seat rail plate.
Disconnect and remove the ECM. (Figure 1) @ ISC Valve Mounting Screw Torque: 2.1± ±0.6 N.m (1.5± ±0.4 lb-ft)! Carefully insert the ISC valve straight into the throttle body hole to prevent damaging the o-ring. Turn the ISC valve slightly to confirm that the o-ring has not twisted. Using the new screw provided in the replacement parts kit, make sure the screw is completely seated on the plate after the screw has been tightened to the specified torque. Remove and replace the ISC valve.
(Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation.! Cover the throttle bodies to prevent anything from dropping into the engine. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box.
(Refer to Service Manual, Page 5-14) REPLACEMENT PROCEDURE: 8. Install the new ECM in reverse order of removal. Apply thread lock to the upper plate mounting bolts when reinstalling the upper seat rail plate. Incoming search terms:.
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1.
Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4.
“E”-clip (keep) 5. Spacer (3) (keep) 6.
Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9.
Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1.
Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual.
Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier.
Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual.
Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws.
Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7.
Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster.
Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84 Incoming search terms:.
REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. Disconnect battery cables, negative (-) battery cable first. Remove seat according to the instructions in the service manual.
Refer to service manual to remove left saddlebag and side cover. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity.
Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1. Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual.
Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual.
Remove engine from chassis following the instructions in the service manual. Disassemble engine top end and bottom end. Refer to appropriate ENGINE sections in service manual. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage.
(00511b) -J04793 1 2 is03517 1. O-ring counterbore 2. Spigot bore Figure 1.
Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in.
(41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in.
(2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2. Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). Remove cylinder studs from the engine crankcase. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas. Inspect and clean engine case mating surfaces.
See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm). See Figure 1 and Table 1.
Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase Incoming search terms:. Remove fuel tank and air filter assembly per Yamaha service manual procedures. Remove the air silencer box under the tank.
Install supplied BA-2410-00 Needle/Jet kit according to the instructions in the jet kit package being sure to use the Jets and Needle Slot setting called out for the external BAK filter assemble. Reinstall the air silencer box under the tank. Remove the rubber boot from the stock air box. It is glued-in from the factory, but will come loose if gently persuaded. See photo #1 Our install guides provide a basic outline on the proper installation of our products.
Further tuning and/or fitment may be required. Barons bears no responsibility on installation costs associated with this product. © 2010 Barons Custom Accessories 7401 Slater Ave.
Huntington Beach, CA 92647 (714)274-4065 – Ph. (714)848-0718 – [email protected] Page: 2 BA-2011-00/03/06/07/13/13B BIG AIR KIT – YAMAHA V-Star 650 6.
2009 Yamaha Raider Manual
Install the stock rubber boot into your new Baron air filter backing plate with the supplied glue. Squeeze glue liberally into sealing groove in stock rubber boot.
See photo #2 Allow glue to set up and dry prior to mounting onto bike Incoming search terms:. INSTALLATION PROCEDURE 1. Secure motorcycle to a bike lift and raise the motorcycle.
Remove stock rear shock from the motorcycle per standard Yamaha shop manual instructions. Place the shaft of the shock in V” blocks and secure this in a vice or press, applying firm pressure to the V” blocks to trap the shaft so it will not turn. Unscrew the upper shock mount eyelet from the shaft. NOTE: The upper mount is a standard thread so you will rotate the mount counter-clockwise to unscrew it. Next, screw the New LA Choppers Shock Mount onto shock shaft using Loctite.
Re-install shock spring, making sure it is locked in place with the retaining ring prior to slowly releasing the spring compressor. Allow shock spring to expand against the retaining ring and machined washer. Reinstall shock onto the motorcycle per standard Yamaha shop manual instructions. WARNING: Installing a lowering kit will decrease initial ground clearance. The motorcycle will be lower to the ground and care should be taken to avoid bottoming, especially over bumps or in turns. To maintain proper balanced geometry, the front and rear of the motorcycle should be lowered equally.
Free Yamaha Owner's Manual
Failure to properly install the lowering kit and operate the motorcycle after installation may result in serious injury or death to the rider. LIMITED GUARANTY: Because we cannot control the application of our products, buyer assumes risks for any and all damage caused to him or herself or any third party by virtue of any failure of these parts. Guaranty for such parts is limited to our replacement costs thereof. This guaranty is in lieu of all other guaranties or warranties express or implied, and all other such guaranties or warranties are hereby expressly disclaimed. By installation of these parts, buyer irrevocably agrees to the foregoing.